Rated to 950 meter (3,116 feet) water depth!

This WetLink Penetrator Blank is used to seal any unused holes on your watertight enclosure with a high-pressure seal. Each set includes a bulkhead, O-ring, and nut. It’s rated to 950 meter (3,116 feet) water depth!  

The WetLink Penetrator is a compression gland cable penetrator to seal electrical cables as they pass into a device or enclosure. Each set includes a bulkhead, seal, plug, O-ring, and nut. It’s rated to 950 meter (3,116 feet) water depth when used with officially recommended cables! 

The WetLink Penetrator is a compression gland cable penetrator to seal electrical cables as they pass into a device or enclosure. Each set includes a bulkhead, seal, plug, O-ring, and nut. It’s rated to 950 meter (3,116 feet) water depth when used with officially recommended cables!  

The WetLink Penetrator is a compression gland cable penetrator to seal electrical cables as they pass into a device or enclosure. Each set includes a bulkhead, seal, plug, O-ring, and nut. It’s rated to 950 meter (3,116 feet) water depth when used with officially recommended cables!  

 The tool holds the WetLink Penetrator bulkhead during assembly and is compatible with M06, M10, and M14 bulkhead sizes. It’s designed to fit in a vice or be bolted to a table. 

 This wrench makes it easy to install the plug of the WetLink Penetrator, creating a high-pressure seal with your cable. It can be turned by hand or with a 1/4″ socket driver and we recommend using it with the WetLink Assembly Block. It’s made of hardened tool steel for a long life. 

This wrench makes it easy to install the plug of the WetLink Penetrator, creating a high-pressure seal with your cable. It can be turned by hand or with a 1/4″ socket driver and we recommend using it with the WetLink Assembly Block. It’s made of hardened tool steel for a long life. 

This vent allows trapped pressure to escape from an enclosure after it has been closed. Based on the cable penetrator design, it includes a threaded plug with double O-ring seal to open and close the vent. 

Four direct-drive underwater thrusters including ”DWT085G1, DWT085D3, DWT110D4, DWT135D4.” The key feature of the direct-drive series is designed to directly transmit torque from the motor without any reduction. Main benefits also include high torque, fast response, and low inertia.    

Three magnetically coupling underwater thrusters including ”DWT6532, DWT6537, and DWT1.” The main feature is there are no mechanical commutators, which naturally could reduce shaft friction and inertia, and create less noise. Also, there are no connecting shafts, which makes them easy to install and remain extremely low maintenance with high reliability.  

 TM-2408 is a digital servo rotator and achieves up to 0.1° positioning accuracy in subsea applications. The robust electromechanical design achieves the extraordinary torque output 7Nm. Its user-friendly evaluation software allows users to adjust and test speed and angle immediately. The unique modular design provides handy maintenance and replacement. The compact size and front view mounting gain an advantage in displaying system layout easily and simplifying installation procedure. 

 PCG-1000 is exclusively designed for subsea inertial positioning and navigation system. The device integrates Pressure, Compass, and Gyroscope into single unit. The pressure sensor has an accuracy of 0.05%FS. . 

Standard Overmold can not only transmit power for subsea instruments at a water depth of 600 Pa, but also stabilize the output signal source for instruments. In addition, this product requires additional self-assembly before use, which is a highly customized product. 

Standard Inline can not only transmit power to subsea instruments at a water depth of 600 Pa, but also can stably output signal sources. In addition, it support customization of various lengths, and able to be equipped with signal sources specified by customers. 

 Standard Bulkhead connector can not only transmit power to the subsea instrument at a water depth of 600 Pa, but also can stably output signal sources. In addition, it can be equipped with a signal source specified by customer. Thread is also conducive to the design of instrument fixing. 

More flexibility and you can specify materials to make products according to current needs. The product is also a modified version of Inline. 

 Micro Overmold is the smallest and the most popular among all waterproof connector series. It can not only transmit power for subsea instruments at a water depth of 600 Pa, but also stabilize the output signal source for the instruments. In addition, this product requires additional self-assembly before use, which is a highly customized product.  

 Micro Inline is the smallest and the most popular among all waterproof connector series. It can not only transmit power for subsea instruments at a water depth of 600 Pa, but also stabilize the output signal source for the instruments. In addition, it supports customization of various lengths and is able to be equipped with signal sources specified by customers. 

 Micro Right Angle is the smallest and most popular of all waterproof connector series. With right-angle design can not only save equipment space configuration but reduce the risk of wire entanglement and wear. In addition, it can transmit subsea instruments at a water depth of 600 Pa. Electricity is the stable output signal source for the instrument. It can also be equipped with a signal source specified by the customer. 

 Micro Bulkhead is the smallest and the most popular among all waterproof connector series. It can not only transmit power for subsea instruments at a water depth of 600 Pa, but also stabilize the output signal source for the instruments. In addition, it can be equipped with a signal source specified by customer. Thread is also conducive to the design of instrument fixing. 

 Low Profile Bulkhead is designed as a profile joint to maximize space efficiency and reduce drag for the device. Low profile not only can transmit power for subsea instruments at a water depth of 600 Pa but also stabilize the output signal source for the instruments. In addition, it can be equipped with a signal source specified by the customer. Thread is also conducive to the design of instrument fixing. 

 Low Profile Bulkhead is designed as a profile joint to maximize space efficiency and reduce drag for the device. Low profile not only can transmit power for subsea instruments at a water depth of 600 Pa but also stabilize the output signal source for the instruments. In addition, it can be equipped with a signal source specified by the customer. Thread is also conducive to the design of instrument fixing. 

Cobalt Series bulkhead connector for use with Cobalt Series Cable, Single-ended or Cobalt Series Cable, Double-ended (sold separately).  Rated to 600 m depth, includes M10 X 1.5 nut.  3-pin, 4-pin, 6-pin, and 8-pin versions available. 

Use this Cable Termination Kit to add a Cobalt connector to your own cable!  Available in 3-pin, 4-pin, 6-pin, or 8-pin versions, with regular or large connector shells. 

 Use this Cable Termination Tool along with the Cable Termination Kit to add a Cobalt connector to your own cable!  Available in 3-pin, 4-pin, 6-pin, or 8-pin versions. 

Polyurethane-jacketed 1-meter cable with Cobalt Series plug and locking sleeve on one end and M6 or M10 Simple Penetrator on the other end.  For use with Cobalt Series Bulkhead Connector (sold separately).  Rated to 600 m depth.  Available with 3, 4, 6, or 8 conductors.  

 Polyurethane-jacketed cable with Cobalt Series plug and locking sleeve on both ends.  For use with Cobalt Series Bulkhead Connector (sold separately).  Rated to 600 m depth.  Available with 3, 4, 6, or 8 conductors, and in a standard 1-meter length or custom lengths from 0.6 to 2.0 meters. 

Polyurethane-jacketed cable with Cobalt Series plug and locking sleeve on one end.  For use with Cobalt Series Bulkhead Connector (sold separately).  Rated to 600 m depth.  Available with 3, 4, 6, or 8 conductors, and in a standard 1-meter length or custom lengths from 0.1 to 2.0 meters. 

Removable locking sleeve for Cobalt Series cables.  This locking sleeve will fit over the connector end of a Cobalt cable and is retained with a split nylon washer.  Useful for situations where you need to be able to remove and replace the locking sleeve. 

 The Simple Penetrator is the most affordable, simple, and reliable way to make a submersible electrical connection.  Simply install a Simple Penetrator on each device or enclosure and connect them with a length of polyurethane tubing (not included).  Then run your wire or cable through the tubing.  The barbed portion of the Simple Penetrator reliably seals to the polyurethane tubing while the O-ring seals to the surface of the device. Available in three versions.

Cobalt Series bulkhead connector for use with Cobalt Series Cable, Single-ended or Cobalt Series Cable, Double-ended (sold separately).  Rated to 600 m depth, includes M10 X 1.5 nut.  3-pin, 4-pin, 6-pin, and 8-pin versions available. 

Use this Cable Termination Kit to add a Cobalt connector to your own cable!  Available in 3-pin, 4-pin, 6-pin, or 8-pin versions, with regular or large connector shells. 

 M10 Thread / Aluminium

BlueROV2 Sized & Compatible.  

 M10 Thread / Aluminium

BlueROV2 Sized & Compatible.    

 7/16th Thread / Brass or Stainless Steel 

Brass or Stainless Steel